The IC693DNM200 is a 90-30 series component manufactured by GE Fanuc. It is a single slot DeviceNet master module with one (1) DeviceNet terminal and one (1) RS232 service port. The module supports standard DeviceNet transfer rates such as 125K, 250K and 500K, is capable of supporting 255 input data bytes and 255 output data bytes and can accommodate up to 63 DeviceNet slave devices.
The IC693DNM200 is a DeviceNet master module. The module is a single slot communication module that is part of the Series 90-30 programmable logic controller (PLC) platform, manufactured by GE Fanuc and now part of Emerson Automation. The module is equipped with a DeviceNet terminal. It also has one (1) RS232 9-pin D-shell female port which is used as a module service port.
The IC693DNM200 supports all data rates of the DeviceNet protocol, in particular 125K, 250K and 500K transfer rates. Each slave can transmit up to 255 bytes of input data and 255 bytes of output data from the host, and up to 3972 bytes of input data and 3972 bytes of output data to this host module. In addition, a total of 126 I/O connections can be established using the module, as it is capable of communicating with up to 63 slave devices, each of which can be assigned up to two (2) I/O stations. The module supports and can be configured for data connections such as polling, pass select, cyclic or COS. this DeviceNet master module also supports explicit messaging, unconnected message manager (UCMM) and one (1) proxy connection per slave unit.
In addition, the module can operate in dual mode, as both a master and a slave. In particular, the fault behaviour during communication loss can be configured to provide an acceptable system response in the event of said error. The module also comes with upgradeable firmware allowing module updates and bug fixes to be downloaded via the RS232 service port.
The IC693DNM200 module is a DeviceNet master module designed and manufactured by GE Fanuc. The unit is part of the 90-30 series and has a wide range of integrated functions for information and data transfer applications. Most of these functions are automatic and the unit works on a DeviceNet network that includes other devices and hosts.The IC693DNM200 module can be mounted on the host rack of a Series 90-30 or PACSystems RX3i system, but is not suitable for remote or expansion racks.The IC693DNM200 DeviceNet module has 32 output points and supports standard data rates such as 125K, 250K and 500K baud. Outputs are available in groups of 4, each group containing 8 points. The unit is rated for 12 to 24 volts DC (positive logic) and its backplane draws 450 mA at 5 volts DC.
The output current of the GE Series 90-30 DeviceNet IC693DNM200 module is 0.5 amps per point, while its inrush current is 5.4 amps for 10 milliseconds. For the output current, it should be noted that the final output current per group is 4 amps, while the output current per common pin group does not exceed 3 amps. In addition to this, the on-state voltage drop is 0.3 volts DC and the on/off response time does not exceed 0.5 ms. The IC693DNM200 module is very reliable and can operate over a temperature range of 0 to 60 degrees Celsius (32 to 140 degrees Fahrenheit). In addition to this, the unit is specified for storage over a temperature range of -40 to 85 degrees Celsius (-40 to 185 degrees Fahrenheit).
VMIVME-7750
IS220PVIBH1A
IS420UCSCH2A
5SHY3545L0010 3BHB013088R0001
3BHE009681R0101 GVC750BE101
ICS TRIPLEX T8310
ICS TRIPLEX T8461
ICS TRIPLEX T8151B
ICS TRIPLEX T8403C
ICS TRIPLEX T8311
ICS TRIPLEX T9402
ICS TRIPLEX T9451
IS215VCMIH2BB
IS215VCMIH2CA
ABB PM866K01 3BSE050198R1
ABB 216NG63
ABB 216VC62a
ABB 216EA61b
ABB 216AB61
ABB 216DB61
ABB REG216
PC control module, is based on PC as a basic development of a control terminal. PC control module is a programmable controller, is used for communication between PC and PC station terminal, mainly used to achieve control data communication function. PC control module has powerful functions, good compatibility, high security, cheap price, simple maintenance, support industrial environment and other characteristics. According to customer requirements for secondary development and production, with high cost performance. PC control module through serial communication technology and analog/digital communication technology and PLC, MCU and other control equipment to achieve communication, can be used in PLC, MCU and other control equipment.
We do other brands: ABB, Allen-Bradley, Schneider, GE (General electric), Westinghouse, FANUC, Bently, KUKA, Foxboro, Triconex, Honeywell, YASKAWA, etc., if you need, you can contact me, look forward to your consultation.
As long as tomorrow is still here, as long as spring is still here!
As long as there is life, as long as there is hope!
As long as tomorrow is still here, as long as the future is still here!
