The IC670CHS001 is an I/O terminal block from the Field Control platform, currently under Emerson Automation, formerly produced by GE Intelligent Platforms (GE IP). This is a Barrier style I/O carrier that comes with 37 terminals that can accommodate up to Two (2) Field control modules. This terminal block accommodates up to Two (2) solid or stranded of copper wires ranging AWG #14 to AWG #22 per terminal. This terminal module is designed for horizontal installation, mounted to a DIN rail or directly to an enclosure subpanel.
The IC670CHS001 is a terminal block module from the Field control series, formerly by GE Fanuc, now under Emerson Automation. This module comes with barrier style terminal blocks which accommodate signal wires to and from electrical loads and signaling devices. It provides modular connectivity as this module permits removal and insertion of hosted I/O modules without the need of removing the existing wiring connections.
The IC670CHS001 also provides backplane communication as this module comes embedded with connector that attaches to the adjacent terminal block module. This terminal block module is capable of hosting up to Two (2) modules, supporting discrete I/O and analog I/O modules.
The IC670CHS001 has a total of 37 termination points. Each terminal can accommodate up to two (2) wires in the size range of #14 (2.1 mm2) to AWG #22 (0.35 mm2). The applicable wire insulation rating is 90 degrees C and the recommended tightening torque is 8 in-lb. For ground terminal wiring, the applicable wire size is AWG #14 (average 2.1 mm2 cross section) and must not exceed 4 inches or 10.16 cm in length.
This junction box module supports horizontal DIN rail or panel mounting. By using the IC670CHS001, hot swapping is possible in non-hazardous application areas when the appropriate Bus Interface Unit (BIU) is installed, especially with BIU modules with firmware version 2.1 or higher. For the connection of one or more terminal bases, the compatible pre-assembled cable used is IC670CBL001. In addition, an auxiliary terminal block can be connected to the module to provide additional ground, signal loop and signal common connections.
The GE Fanuc Field Control IC670CHS001 is a barrier style terminal block that can have host up to Filed Control modules. it, enabling communications between modules connected into its backplane and serving as endpoint terminals for connections to external field devices. They support the installation of 2 modules. These modules are mechanically screwed to the GE Fanuc IC670CHS001 I/O base in order to avoid accidental disconnections due to equipment vibration. The I/O base terminal block comes from the factory with protective barriers that prevent contact with adjacent cables and short circuits during the connection or disconnection of devices. An important thing to take note of is that these modules support the connection and disconnection of cabling even while the module is powered on.
There are 37 screw terminals in a GE Fanuc IC670CHS001 I/O base. Two of those terminals, marked as terminals A and B, are for power supply connections and the remaining 35 are used for individual terminal connections. The terminals can accommodate AWG #14 (2.1 square millimeters) through AWG #22 (0.35 square millimeters) cables. The GE Fanuc IC670CHS001 I/O base is keyed in order to avoid the incorrect connections of additional I/O modules. These additional modules are mounted onto the base by pressing them firmly against it once they have been placed in the right positions. It is always necessary to tighten the screws of the module into the base, in order to prevent vibrations from disconnecting the modules from the I/O base. The manufacturer recommends using a maximum torque of 8 to 10 pounds on an inch.IC670CHS001
VMIVME-7750
IS220PVIBH1A
IS420UCSCH2A
5SHY3545L0010 3BHB013088R0001
3BHE009681R0101 GVC750BE101
ICS TRIPLEX T8310
ICS TRIPLEX T8461
ICS TRIPLEX T8151B
ICS TRIPLEX T8403C
ICS TRIPLEX T8311
ICS TRIPLEX T9402
ICS TRIPLEX T9451
IS215VCMIH2BB
IS215VCMIH2CA
ABB PM866K01 3BSE050198R1
ABB 216NG63
ABB 216VC62a
ABB 216EA61b
ABB 216AB61
ABB 216DB61
ABB REG216
PC control module, is based on PC as a basic development of a control terminal. PC control module is a programmable controller, is used for communication between PC and PC station terminal, mainly used to achieve control data communication function. PC control module has powerful functions, good compatibility, high security, cheap price, simple maintenance, support industrial environment and other characteristics. According to customer requirements for secondary development and production, with high cost performance. PC control module through serial communication technology and analog/digital communication technology and PLC, MCU and other control equipment to achieve communication, can be used in PLC, MCU and other control equipment.
We do other brands: ABB, Allen-Bradley, Schneider, GE (General electric), Westinghouse, FANUC, Bently, KUKA, Foxboro, Triconex, Honeywell, YASKAWA, etc., if you need, you can contact me, look forward to your consultation.
As long as tomorrow is still here, as long as spring is still here!
As long as there is life, as long as there is hope!
As long as tomorrow is still here, as long as the future is still here!
