The IC697MDL940 is a Series 90-70 Programmable Logic Controller (PLC) module, specifically a Relay output module with a total of Sixteen (16) relay output channels. Specifically, it has Eight (8) Form C Contact outputs and Eight (8) Form A or Normally Open (N.O.) in Two (2) groups of Four (4) Form A contacts each channel. This module has a nominal voltage rating of 120/240 VAC or 5/24/125 VDC with a maximum power consumption of 480 VA for AC loads or 60 watts for DC loads. It has maximum load current ratings of 2.0 amps from 5 to 265 VAC at 47-63 Hz; 2.0 amps from 5 to 30 VDC; 0.2 amps from 31 to 125 VDC and 0.2 amps from 31 to 150 VDC applicable for Form A contact outputs only while the module’s minimum load current is 10 mA. Each output channel has a maximum response time of 10 ms for both On and Off signal transition and switching frequency of 20 Cycles per minute when used with an inductive load. The output relays of this module are fixed coil, moving armature type while the output contacts are made of silver alloy with a maximum contact resistance of 0.2 Ohm and expected contact life of 20,000,000 operations for mechanical operations and 1,000,000 electrical operations at resistive inductive load. Each output of the IC697MDL940 is installed with a 3 Ampere fuse used as built-in channel protection along a snubber circuit which consists of a 47 Ohm resistor and capacitor with 0.015 µfd capacitance value.
The IC697MDL940 output relay module is an output relay module designed and manufactured by GE Fanuc. The module is typically used with GE PLC devices from Series 90-70 and it is equipped with 3-Amp rated fuses for protection. The module has a typical contact life of 300,000 to 1,000,000 operations and it has a maximum load current of 0.1 to 2 Amps for a resistive load and 0.05 to 1 Amp for a inductive load. This particular GE Fanuc module is designed for both AC and DC operation and it includes operating voltage ratings of 120 to 240 Volts AC or 5, 24, or 125 Volts DC. The module has 16 outputs and it features an operating frequency of 47 to 63 Hertz (for AC voltage only). The configuration of the output points includes 8 points configured in Form C and same number of points configured in Form A. The output points in Form C are isolated and other points are placed in 2 groups.
VMIVME-7750
IS220PVIBH1A
IS420UCSCH2A
5SHY3545L0010 3BHB013088R0001
3BHE009681R0101 GVC750BE101
ICS TRIPLEX T8310
ICS TRIPLEX T8461
ICS TRIPLEX T8151B
ICS TRIPLEX T8403C
ICS TRIPLEX T8311
ICS TRIPLEX T9402
ICS TRIPLEX T9451
IS215VCMIH2BB
IS215VCMIH2CA
ABB PM866K01 3BSE050198R1
ABB 216NG63
ABB 216VC62a
ABB 216EA61b
ABB 216AB61
ABB 216DB61
ABB REG216
PC control module, is based on PC as a basic development of a control terminal. PC control module is a programmable controller, is used for communication between PC and PC station terminal, mainly used to achieve control data communication function. PC control module has powerful functions, good compatibility, high security, cheap price, simple maintenance, support industrial environment and other characteristics. According to customer requirements for secondary development and production, with high cost performance. PC control module through serial communication technology and analog/digital communication technology and PLC, MCU and other control equipment to achieve communication, can be used in PLC, MCU and other control equipment.
We do other brands: ABB, Allen-Bradley, Schneider, GE (General electric), Westinghouse, FANUC, Bently, KUKA, Foxboro, Triconex, Honeywell, YASKAWA, etc., if you need, you can contact me, look forward to your consultation.
As long as tomorrow is still here, as long as spring is still here!
As long as there is life, as long as there is hope!
As long as tomorrow is still here, as long as the future is still here!
