The IC697BEM711 is a Bus Interface Module (BEM) that is used for implementing rack expansion. Specifically, this module is a Bus Receiver module. Utilization of this module allows installation of additional I/O and specialty modules and permits installation of up to Seven (7) expansion racks. This module has Two (2) communication interfaces, with port 1 used as an expansion port for establishing a connection to the CPU or other BEM 711 and BEM 713. The other communication interface is used as an expansion port out for connecting to expansion racks or other BEM 711 modules. The permitted between each BEM 711 or BEM 713 is 50 feet or 15 meters. The IC697BEM711 is not limited to rack expansion. System fault isolation can also be achieved as data transmitted to and from the communication cables are low-level signals representing the data available to an expansion rack. Troubleshooting and maintenance are also simplified as an expansion rack can be isolated for troubleshooting. Furthermore, output hold may also be implemented, enabling output modules of a failed or rack under maintenance to retain individual last state. This module is also provided with Three (3) stats LED indicators for indicating Rack OK, Last Rack, and Bus Active. This module is purely configured using the MS-DOS or Windows Programming software packages. The last expansion rack must be installed with a terminating resistor with catalog number IC697ACC702. This component is necessary to signal the end of the network and identify the last node of the expanded configuration. This module supports a transmission rate of 500 Kbytes/sec and a backplane current consumption of 800 mA.
The IC697BEM711 module is a bus receiver module. Features of the IC697BEM711 module include a high-speed parallel bus expansion interface, support for 7 expansion racks, system fault isolation, easy software configuration, and support for holding the machine’s last state. Three LED indicators on the module provide the status of the module as well as the bus expansion port status and expansion status. By using the IC697BEM711 module, expansion to up to a maximum of 7 additional IC697 PLC racks can be achieved by using a total of 15 meters of cable. The IC697BEM711 module takes up one slot in the PLC chassis. Two connectors are provided on the module’s front panel: one connector is used to connect with the upstream or CPU rack and the other connector is used to connect to additional expansion racks through a daisy chain arrangement.
The IC697BEM711 bus receiver module needs to be configured using the Windows or MS-DOS programming software function. The current requirement of the module is 0.8 Amps and the module also requires 5 Volts DC input voltage. The expansion interface can transmit data at up to 500 kilobytes per second. A cable measuring up to 15 meters can be used with the expansion interface. The module is designed to support VME standard C.1. When ordering the module, the terminator plug with catalog number IC697ACC702 can also be ordered. Furthermore, the following I/O cables can be ordered: a 5-foot cable with the catalog number IC600WD005A, a 10-foot cable with the catalog number IC600WD010A, a 25-foot cable with the catalog number IC600WD025A, and a 50-foot cable with the catalog number IC600WD050A. System power must be turned off before the IC697BEM711 module is inserted into the slot designated for it.
VMIVME-7750
IS220PVIBH1A
IS420UCSCH2A
5SHY3545L0010 3BHB013088R0001
3BHE009681R0101 GVC750BE101
ICS TRIPLEX T8310
ICS TRIPLEX T8461
ICS TRIPLEX T8151B
ICS TRIPLEX T8403C
ICS TRIPLEX T8311
ICS TRIPLEX T9402
ICS TRIPLEX T9451
IS215VCMIH2BB
IS215VCMIH2CA
ABB PM866K01 3BSE050198R1
ABB 216NG63
ABB 216VC62a
ABB 216EA61b
ABB 216AB61
ABB 216DB61
ABB REG216
PC control module, is based on PC as a basic development of a control terminal. PC control module is a programmable controller, is used for communication between PC and PC station terminal, mainly used to achieve control data communication function. PC control module has powerful functions, good compatibility, high security, cheap price, simple maintenance, support industrial environment and other characteristics. According to customer requirements for secondary development and production, with high cost performance. PC control module through serial communication technology and analog/digital communication technology and PLC, MCU and other control equipment to achieve communication, can be used in PLC, MCU and other control equipment.
We do other brands: ABB, Allen-Bradley, Schneider, GE (General electric), Westinghouse, FANUC, Bently, KUKA, Foxboro, Triconex, Honeywell, YASKAWA, etc., if you need, you can contact me, look forward to your consultation.
As long as tomorrow is still here, as long as spring is still here!
As long as there is life, as long as there is hope!
As long as tomorrow is still here, as long as the future is still here!
